MB:NEX001

From LEXWiKi

(Difference between revisions)
Jump to: navigation, search
Current revision (10:06, 16 December 2024) (edit) (undo)
(→FAQ of NEX-001)
 
(7 intermediate revisions not shown.)
Line 54: Line 54:
[{{SERVER}}/lexwiki/index.php?title=Special:TableEdit&id=f777871962f1c0432784d4e0e73802b8.1766.O63a4166f74e02&page=1766&pagename={{FULLPAGENAMEE}} edit table]
[{{SERVER}}/lexwiki/index.php?title=Special:TableEdit&id=f777871962f1c0432784d4e0e73802b8.1766.O63a4166f74e02&page=1766&pagename={{FULLPAGENAMEE}} edit table]
<!--box uid=f777871962f1c0432784d4e0e73802b8.1766.O63a4166f74e02-->
<!--box uid=f777871962f1c0432784d4e0e73802b8.1766.O63a4166f74e02-->
 +
 +
 +
'''Porting Guide and YOCTO Image download path below'''
 +
 +
https://www.lex.com.tw/en/download/download-hide?cid1=67&cid2=192#topDownload
 +
== FAQ of NEX-001 ==
== FAQ of NEX-001 ==
Line 89: Line 95:
[[Image:NEX-001_sw_butten.jpg]] [[Image:NEX-001_sw.jpg]]
[[Image:NEX-001_sw_butten.jpg]] [[Image:NEX-001_sw.jpg]]
 +
 +
|-
 +
|}
 +
 +
=== How to use test & debug (NXP default UART)? ===
 +
{|
 +
{|
 +
!bgcolor = #ccccff width="50" align="center"|Ans:
 +
!bgcolor = #F3F3F3 width="100%" align="left"|
 +
 +
Connect UART Debug Cable (cc1)
 +
 +
[[Image:NEX-001_CC1.jpg]]
 +
 +
Open the terminal window
 +
(i.e., Hyper Terminal or Tera Term)，choose the COM port number and apply the following configuration.
 +
 +
Baud rate: 115200
 +
 +
Data bit: 8
 +
 +
Parity: None
 +
 +
Stop bits: 1
 +
 +
[[Image:NEX-001_tera_term.jpg]]
|-
|-
Line 107: Line 139:
3.use TYPE-A cable in NEX-001 USB(CU1)
3.use TYPE-A cable in NEX-001 USB(CU1)
 +
 +
[[Image:NEX-001_USB(CU1).jpg]]
4.NEX-001 use Serial Download mode
4.NEX-001 use Serial Download mode
Line 113: Line 147:
test@ubuntu:~$ sudo uuu -b emmc_all imx-boot-imx8mpevk-sd.bin-flash_evk imx-image-multimedia-imx8mpevk-20230201090156.rootfs.wic.bz2
test@ubuntu:~$ sudo uuu -b emmc_all imx-boot-imx8mpevk-sd.bin-flash_evk imx-image-multimedia-imx8mpevk-20230201090156.rootfs.wic.bz2
-
 
-
6.Finally you can see end message
 
-
uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.243-0-ged48c51
+
5.1 use uuu command, image to sd
 +
 
 +
test@ubuntu:~$ sudo uuu -b sd_all imx-boot-imx8mpevk-sd.bin-flash_evk imx-image-multimedia-imx8mpevk-20230201090156.rootfs.wic.bz2
 +
 
 +
6.Finally you can see end message
-
Success 1 Failure 0
+
[[Image:NEX-001_flash_image.jpg]]
[https://www.lex.com.tw/zh-tw/download/download-hide?cid1=67&cid2=192#top%E4%B8%8B%E8%BC%89 NEX-001 image]
[https://www.lex.com.tw/zh-tw/download/download-hide?cid1=67&cid2=192#top%E4%B8%8B%E8%BC%89 NEX-001 image]

Current revision

Contents

Driver Support

O.S.REVKernelHDMILAN1LAN2EMMCSD CARDEEPROMUSB 2.0/3.0(host)USB 2.0/3.0(device)UART DebugUART RS232UART RS485CAN1CAN2DownloadPatch

Yocto

0.2

5.4.70-2.3.2

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

edit table


Porting Guide and YOCTO Image download path below

https://www.lex.com.tw/en/download/download-hide?cid1=67&cid2=192#topDownload


FAQ of NEX-001

How to check NEX-001 ?

Ans:


If you want to check the hardware function, you can connect the device yourself to test whether it works normally

Unless you need to check a large number of NEX-001, you can also refer to the detection tool we made

Image:NEX-001.jpg

NEX-001 hardware function test

How to choose Boot Switch mode?

Ans:

NEX-001 has three modes for users to choose, please refer to the picture to switch the required mode.

Serial Download mode allows users to flash IMAGE files

EMMC boot, start the operating system in EMMC

SD card boot , start the operating system in SD card

Image:NEX-001_sw_butten.jpg Image:NEX-001_sw.jpg

How to use test & debug (NXP default UART)?

Ans:

Connect UART Debug Cable (cc1)

Image:NEX-001_CC1.jpg

Open the terminal window (i.e., Hyper Terminal or Tera Term)，choose the COM port number and apply the following configuration.

Baud rate: 115200

Data bit: 8

Parity: None

Stop bits: 1

Image:NEX-001_tera_term.jpg

How to use uuu for eMMC or SD card in NEX-001?

Ans:

1.Platform is linux, we take Ubuntu 20.04.4 LTS for sample

2.Install uuu(Universal Update Utility), this action requires network or use floder uuu open terimal( Ctrl+alt+t ) 

  test@ubuntu:~$ snap install universal-update-utility

3.use TYPE-A cable in NEX-001 USB(CU1)

Image:NEX-001_USB(CU1).jpg

4.NEX-001 use Serial Download mode

5.use uuu command, image to emmc 

  test@ubuntu:~$ sudo uuu -b emmc_all imx-boot-imx8mpevk-sd.bin-flash_evk imx-image-multimedia-imx8mpevk-20230201090156.rootfs.wic.bz2

5.1 use uuu command, image to sd 

   test@ubuntu:~$ sudo uuu -b sd_all imx-boot-imx8mpevk-sd.bin-flash_evk imx-image-multimedia-imx8mpevk-20230201090156.rootfs.wic.bz2

6.Finally you can see end message

Image:NEX-001_flash_image.jpg

NEX-001 image

Retrieved from "http://tprd.info/lexwiki/index.php/MB:NEX001"
Personal tools