請先看『使用說明』

From LEXWiKi

Revision as of 14:38, 28 October 2020

The Sample code source you can download from

Source file: CIO_Utility_Src_v3.0.7.1_w.zip

Binary file: CIO_Utility_Bin_v3.0.7.1_x32_w.zip CIO_Utility_Bin_v3.0.7.1_x64_w.zip

F75113 DLL : F75113.dll

MB Support List

edit table

How to use this Demo Application

Attention Please:You must be install vcredist_x86.exe when first time you run the F75111_DIO.exe DEMO AP,The vcredist_x86.exe include all required DLL file.

1. Press the select your test "2i2o"，"4i4o"，"4i4o*2"，"F75111CIO116"，"F75113CIO116"，"8i+8o"，"1i1o"

2. start test，select single mode or looptest

F75111 Layout Picture

Introduction F75111

Initial Internal F75111 port address (0x9c)

   define GPIO1X, GPIO2X, GPIO3X to input or output 
   and Enable WDT function pin 

Set F75111 DI/DO ( sample code as below Get Input value/Set output value )

   DO: InterDigitalOutput(BYTE byteValue))
   DI: InterDigitalInput()

PULSE mode

Sample to setting GP33, 32, 31, 30 output 1mS low pulse signal.

{ 
    this->Write_Byte(F75111_INTERNAL_ADDR, GPIO3X_PULSE_CONTROL,       0x00);             //This is setting low,Level output
    this->Write_Byte(F75111_INTERNAL_ADDR, GPIO3X_PULSE_WIDTH_CONTROL, 0x01);             //This selects the pulse width to 1mS
    this->Write_Byte(F75111_INTERNAL_ADDR, GPIO3X_CONTROL_MODE,        0x0F);             //This is setting the GP33, 32, 31, 30 to output function.    
    this->Write_Byte(F75111_INTERNAL_ADDR, GPIO3X_Output_Data ,        0x0F);             //This is setting the GP33, 32, 31, 30 output data.
}

Initial internal F75111

void F75111::InitInternalF75111()
{
    this->Write_Byte(F75111_INTERNAL_ADDR,GPIO1X_CONTROL_MODE  ,0x00);        //set GPIO1X to Input  function     
    this->Write_Byte(F75111_INTERNAL_ADDR,GPIO3X_CONTROL_MODE  ,0x00);        //set GPIO3X to Input  function
    this->Write_Byte(F75111_INTERNAL_ADDR,GPIO2X_CONTROL_MODE  ,0xFF);        //set GPIO2X to Output function
    this->Write_Byte(F75111_INTERNAL_ADDR,GPIO2X_OUTPUT_DRIVING,0xFF);        //set GPIO2X to Output Drving 

    this->Write_Byte(F75111_INTERNAL_ADDR,F75111_CONFIGURATION, 0x03);        //Enable WDT OUT function
}

Set output value

void F75111::InterDigitalOutput(BYTE byteValue)
{
     BYTE byteData = 0;
     byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue;
     byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue;
     byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue;
     byteData = (byteData & 0x80 )? byteValue + 0x08 : byteValue;
     byteData = (byteData & 0x40 )? byteValue + 0x10 : byteValue;
     byteData = (byteData & 0x20 )? byteValue + 0x20 : byteValue; 
     byteData = (byteData & 0x10 )? byteValue + 0x40 : byteValue;
     byteData = (byteData & 0x08 )? byteValue + 0x80 : byteValue;           // get value bit by bit
   
     this->Write_Byte(F75111_INTERNAL_ADDR,GPIO2X_OUTPUT_DATA,byteData);    // write byteData value via GPIO2X output pin
}

Get Input value

BYTE F75111::InterDigitalInput()
{
    BYTE byteGPIO1X = 0;
    BYTE byteGPIO3X = 0;
    BYTE byteData   = 0;

    this->Read_Byte(F75111_INTERNAL_ADDR,GPIO1X_INPUT_DATA,&byteGPIO1X) ;   // Get value from GPIO1X
    this->Read_Byte(F75111_INTERNAL_ADDR,GPIO3X_INPUT_DATA,&byteGPIO3X) ;   // Get value from GPIO3X	

    byteGPIO1X = byteGPIO1X  & 0xF0;                                        // Mask unuseful value
    byteGPIO3X = byteGPIO3X  & 0x0F;                                        // Mask unuseful value

    byteData = ( byteGPIO1X & 0x10 )? byteData + 0x01 : byteData;
    byteData = ( byteGPIO1X & 0x80 )? byteData + 0x02 : byteData;
    byteData = ( byteGPIO1X & 0x40 )? byteData + 0x04 : byteData;	
    byteData = ( byteGPIO3X & 0x01 )? byteData + 0x08 : byteData;
	
    byteData = ( byteGPIO3X & 0x02 )? byteData + 0x10 : byteData;
    byteData = ( byteGPIO3X & 0x04 )? byteData + 0x20 : byteData;
    byteData = ( byteGPIO3X & 0x08 )? byteData + 0x40 : byteData;
    byteData = ( byteGPIO1X & 0x20 )? byteData + 0x80 : byteData;           // Get correct DI value from GPIO1X & GPIO3X
	
    return byteData;
}

define F75111 pin in F75111.h

//--------------------------------------------------------------------------------------------------------
#define    F75111_INTERNAL_ADDR        0x9C   //  OnBoard  F75111 Chipset
#define    F75111_EXTERNAL_ADDR        0x6E   //  External F75111 Chipset
//--------------------------------------------------------------------------------------------------------
#define    F75111_CONFIGURATION        0x03   //  Configure GPIO13 to WDT2 Function
//--------------------------------------------------------------------------------------------------------
#define    GPIO1X_CONTROL_MODE         0x10   //  Select Output Mode or Input Mode
#define    GPIO2X_CONTROL_MODE         0x20   //  Select GPIO2X Output Mode or Input Mode 
#define    GPIO3X_CONTROL_MODE         0x40   //  Select GPIO3X Output Mode or Input Mode 
//--------------------------------------------------------------------------------------------------------
#define    GPIO1X_INPUT_DATA           0x12   //  GPIO1X Input Data Register
#define    GPIO3X_INPUT_DATA           0x22   //  GPIO2X Input Data Register
#define    GPIO3X_INPUT_DATA           0x42   //  GPIO3X Input Data Register
//--------------------------------------------------------------------------------------------------------
#define    GPIO1X_OUTPUT_DATA          0x11   //  GPIO1X Output Data Register
#define    GPIO2X_OUTPUT_DATA          0x21   //  GPIO2X Output Data Register 
#define    GPIO3X_OUTPUT_DATA          0x41   //  GPIO3X Output Data Register
//--------------------------------------------------------------------------------------------------------
#define    GPIO1X_OUTPUT_DRIVING       0x1B   //  Select GPIO1X Output Driving Enable
#define    GPIO2X_OUTPUT_DRIVING       0x2B   //  Select GPIO2X Output Driving Enable
#define    GPIO3X_OUTPUT_DRIVING       0x4B   //  Select GPIO3X Output Driving Enable
//--------------------------------------------------------------------------------------------------------
#define    GPIO1X_PULSE_CONTROL        0x13   //  GPIO1x Level/Pulse Control Register
                                              //  0:Level Mode 
                                              //  1:Pulse Mode
#define    GPIO1X_PULSE_WIDTH_CONTROL  0x14   //  GPIO1x Pulse Width Control Register
#define    GP1_PSWIDTH_500US           0x00   //  When select Pulse mode:	500	us.
#define    GP1_PSWIDTH_1MS             0x01   //  When select Pulse mode:	1	ms.
#define    GP1_PSWIDTH_20MS            0x02   //  When select Pulse mode:	20	ms.
#define    GP1_PSWIDTH_100MS           0x03   //  When select Pulse mode:	100	ms.
//--------------------------------------------------------------------------------------------------------
#define    GPIO2X_PULSE_CONTROL        0x23   //  GPIO2x Level/Pulse Control Register
                                              //  0:Level Mode 
                                              //  1:Pulse Mode
#define    GPIO2X_PULSE_WIDTH_CONTROL  0x24   //  GPIO2x Pulse Width Control Register
#define    GP2_PSWIDTH_500US           0x00   //  When select Pulse mode:	500	us.
#define    GP2_PSWIDTH_1MS             0x01   //  When select Pulse mode:	1	ms.
#define    GP2_PSWIDTH_20MS            0x02   //  When select Pulse mode:	20	ms.
#define    GP2_PSWIDTH_100MS           0x03   //  When select Pulse mode:	100	ms.
//--------------------------------------------------------------------------------------------------------
#define    GPIO3X_PULSE_CONTROL        0x43   //  GPIO3x Level/Pulse Control Register
                                              //  0:Level Mode 
                                              //  1:Pulse Mode
#define    GPIO3X_Output_Data          0x41   //  GPIO3x Output Data Register 
#define    GPIO3X_PULSE_WIDTH_CONTROL  0x44   //  GPIO3x Pulse Width Control Register
#define    GP3_PSWIDTH_500US           0x00   //  When select Pulse mode:	500	us.
#define    GP3_PSWIDTH_1MS             0x01   //  When select Pulse mode:	1	ms.
#define    GP3_PSWIDTH_20MS            0x02   //  When select Pulse mode:	20	ms.
#define    GP3_PSWIDTH_100MS           0x03   //  When select Pulse mode:	100	ms.
//--------------------------------------------------------------------------------------------------------

Introduction F75113

F75113 Layout Picture

Base on 75113.Dll API function as below list

F75113_API bool _stdcall F75113_Init();
F75113_API BYTE	F75113_GetDigital_Low_Input();                   //BDI0-BDI7
F75113_API BYTE	F75113_GetDigital_High_Input();                  //BDI8-BDI15
F75113_API void	F75113_SetDigital_Low_Output(BYTE byteValue);    //BDO0-BDO7
F75113_API void	F75113_SetDigital_High_Output(BYTE byteValue);   //BDO8-BDO15

F75113_API void	F75113_SetWDT_Enable(BYTE byteTimer);            //For the F75113 on board 
F75113_API void	F75113_SetWDT_Disable();                         //For the F75113 on board