Module:COMMUNICATION

edit table

Wireless Modules:
USB:
Ralink2571 VIA6656 RT5390U

MiniPCI:
Ralink2561 VIA6655

 file: vt6655-ndiswrapper_bin_06282007.run.tgz (binary for fc7 only)
      ndiswrapper-1.47.tar.gz  (src for fc5,6,7)

USB-ADSL Modem: (A&B Version)
Kernel2.4.x Kernel2.6.x

USB-ISDN:
Kernel2.4 For Kernel2.6 FAQ

usb-56k Modem:
supported by kernel

3G module:
Gobi3000

N/A

Leon 08/01/16

Leon 08/01/16

Test on: Ubuntu 10.10

1.Download Driver(3572) Firmware(2870)
2.Disable 2870 default driver for kernel

   #vi /etc/modprbe.d/blacklist.conf
   Blacklist rt2800usb
   Blacklist rt2x00lib
   Blacklist rt2x00usb
   #modprobe –r rt2800usb
   #reboot

2.compile driver

   #vi os/linux/config.mk
   HAS_WPA_SUPPLICANT=y
   HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
   #make 
   #make install

3.copy firmware

   cp rt2870.bin /lib/fireware/

Driver(3572) Firmware(2870)

N/A

Steve 2011/03/11

Steve 2011/03/11

USB-Modem     USB-ADSL      USB-ISDN      USB-Wireless    MiniPCI-Wireless
TESTED M/B:   TESTED M/B:   TESTED M/B:   TESTED M/B:     TESTED M/B:
1. CV860A     1. CV860A     1. CV860A     1. CV860A       1. CV763
2. MV823A     2. MV823A     2. MV823A
3. CI852A     3. CI852A
4. CV700x

N/A

N/A

Denny 01/24/07

Denny 01/24/07

1. Cologne USD-ISDN 該如何在Kernel 2.6.x環境下使用? USB-ISDN 我們將不再提供特定Driver給客戶,因為目前Kernel 2.6.x幾乎都整合了ISDN4Linux module,而客戶在Kernel 2.6.x環境下看不到ISDN設備是因為Kernel default 將HFC-S這個模組關閉, 只要將模組載入即可使用.

請在Kernel 2.6.x環境下 注意是否以載入 HFS –S 模組 如下圖: 請使用lsmod 指令

在確認硬體裝置狀態 請始用dmesg指令

若沒有發現上述內容,請選擇step1 or step2 完成ISDN 安裝

Step1. Recompile Kernel 將HFC-S 模組打開 並載入.
        請使用make menuconfig 選擇需要模組
        開啟
        Device Drivers ->ISDN subsystem ->old ISDN4Linux ->Passive Cards ->HFC usb base modem.
        再重新載入新編譯的kernel即可.
Step2. 請安裝ISDN4Linux模組,詳細請參照patch file
        Dial-up 方式
        可使用ISDN4Linux Tools 或是 使用xwindows 網路工具
        1. X windows dial-up
            請選擇 “Billion ISDN”or “Cologne USB ISDN”即可使用.

2. 我們的USB-ISDN不是128K 怎麼會只有64K? Cologne USB-ISDN 為2 Channel ISDN(實體層獨立通道),單一Channel各為64K,要使用128K雙通道, 請於撥接時 如下圖設定. 使用Channel Bundling 可自動Dial-up 雙通道,並依流量需求自動調整64K or 128K.

ISDN4Linux http://www.isdn4linux.de/

N/A

Robert 05/22/07

Leon 05/23/07

Please follow the procedure to install Conexant USB ADSL Modem.

A.Make sure your kernel supported !!

1.

 #make menuconfig

2.choose module

 [ Networking ]
          [ Networking support ]
                [ Networking options ]   -> [M] Asynchronous Transfer Mode
                                            [M] RFC1483/2684 Bridged protocols
 [ Device Drivers ]
          [ USB support ]
                [ USB DSL Modem support] -> [M] USB DSL modem support
                                            [M] speedtouch USB support
                                            [M] Conexant AccesRunner USB support

If your kernel not include that's modules ,you should be compile and reboot with new kernel.

B.Install lib file and load firmware

(For Fedora)

1.Install lib file by yum

#yum install  linux-atm  linux-atm-libs linux-atm-libs-devel

2.Install rp-pppoe by yum

#yum install rp-pppoe

3.Please download the USB_ADSL_2.6.X.tar file and copy the new firmware in it to /lib/firmware

#cp cxacru-fw.bin /lib/firmware/

4.Connected USB-ADSL device to manboard.

(For CentOS)

1.Please download the USB_ADSL_2.6.X.tar file and install lib files

#rpm -ivh linux-atm-2.5.0-5.i386.rpm 
#rpm -ivh linux-atm-libs-2.5.0-5.i386.rpm 
#rpm -ivh linux-atm-libs-devel-2.5.0-5.i386.rpm

2.Install rp-pppoe by yum

#yum install rp-pppoe

3.Please download the USB_ADSL_2.6.X.tar file and copy the new firmware in it to /lib/firmware

#cp cxacru-fw.bin /lib/firmware/

4.Please download the USB_ADSL_2.6.X.tar file and copy the br2684ctl file to /sbin

#cp br2684ctl /sbin

5.Connected USB-ADSL device to manboard.

(For Ubuntu)

1.Install lib file by apt

#apt-get install  libatm1  libatm1-dev atm-tools

2.Install rp-pppoe by apt

#apt-get install br2684ctl

3.Please download the USB_ADSL_2.6.X.tar file and copy the new firmware in it to /lib/firmware

#cp cxacru-fw.bin /lib/firmware/

4.Connected USB-ADSL device to manboard.

C.USB ADSL Modem connection

1.Load br2684 modules

#modprobe br2684

2.Configure your ISP.

For example : br2684ctl -b -c 0 -a 0.8.32 # VPI = 8 VCI = 32

3.Check USB-ADSL devices

#inconfig -a

you should saw the message as below

nas0      Link encap:Ethernet  HWaddr 00:05:B4:12:41:F6
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

4.Setup you dial-up user name and passwd ,select "nas0" for connect device (For Fedora / CentOS)

 #pppoe-setup

(For Ubuntu)

 #pppoeconf		

5.Connect to Internet

#adsl-start

USB_ADSL_2.6.X.tar

N/A

Patty 17:36, 16 January 2009 (CST)

Patty 17:36, 16 January 2009 (CST)

1. Unzip the package tar zxvf usbadsl.tar.gz

2. Shift to the folder cd usbadsl

3. Compilation make cp CnxE2FW.bin /etc/

4. Install the modules

insmod e2.o
lsmod (check e2.o exist or not )
./startADSL
ifconfig hsb0 up
./dhcpd hdb0

5. Setting with web browser (http://10.0.0.2)

(you can find the account and password in Readme file)

6.adsl account and password

in WAN SETTING :

7. Connect:

switch to ppp page and press the execute button

USB_ADSL_2.4.X.tar

n/a

Denny 2009/01/21

Denny 2009/01/21

1.Detect the AL-56UH and the baudrate

 $wvdialconf /etc/wvdial.conf
 
 refer to below picture,AL-56UH can communicate with 115200 and 230400 baudrate.
 

2.Set the baudrate

 $vi /etc/wvdial.conf
 
 

3.Connect to the internet

 $wvdial
 

Refer to below picture,AL-56UH USB Modem can communicates at 115200 and 230400 baudrate.

N/A

N/A

Gordon 2009/07/23 10:00

Patty 2009/07/23 17:30

Should insmod 8139too.ko,8139cp.ko,mii.ko,pci_hotplug.ko,shpchp.ko

N/A

N/A

I-Ling 01.21.2010 , 02:00

Patty 01.28.2010 , 17:07

Install driver v1.20.03

installed and run OK: Fedora core 12 、 Ubuntu 9.10 、Ubuntu 10.04

"VNT6656" "VNT6655"

"N/A"

"Steve 2010/03/10"

"Steve 2010/03/10"

RT2572:

   #lsmod | grep rt2500
   if no message be showed on terminal ,please type below command:
   #modprobe rt2500

RT2571:

   download bin file
   #tar -zxvf RT2571(RT73)_binfile.tar.gz
   #cp rt73.bin /lib/firmware/  
   #modprobe -r rt73usb
   #modprobe rt73usb

RT2561:

  download driver source code
  #tar -zxvf 2009_0123_RT61_Linux_STA_v1.1.2.3.tar.bz2
  #cd 2009_0123_RT61_Linux_STA_v1.1.2.3
  #cd Module 
  #cp rt2561.bin /lib/firmware/
  #cp rt2561s.bin /lib/firmware/ 
  #apt-get update
  #apt-get install linux-header-xxx(kernel version)
  #apt-get insatll linux-kbuild
  #make KBUILD_NOPEDANTIC=1
  #make install
  #modprobe rt61

N/A

N/A

Philip & 2010/08/31

Steve & 2010/09/07

In Debian 6.0 , need to change "auth" to "noauth" in "/etc/ppp/option" first(don't need in other distribution)

find the below words in /etc/ppp/option , and change "auth" to "noauth"
# Require the peer to authenticate itself before allowing network
# packets to be sent or received.
# Please do not disable this setting. It is expected to be standard in
# future releases of pppd. Use the call option (see manpage) to disable
# authentication for specific peers.
auth

In Fedora , need the step to add nameserver first(don't need in other distribution)

#vi /etc/resolv.conf

add the following words:

nameserver 168.95.1.1
nameserver 168.95.192.1

1.modprobe module usbserial

A.In Fedora 16 , need to add into grub
#vi /etc/default/grub
add the following to the end “usbserial.vendor=0x0fcf usbserial.product=0×1008″ 
so that we have something like this

#grub2-mkconfig > /boot/grub2/grub.cfg
#reboot

B.In other distriburion
#modprobe usbserial product=0x14F1 vendor=0x12D1

2.connect

#echo 'ATZ' > /dev/ttyUSB2
#echo 'AT+CGDCONT=1,"IP","INTERNET"' > /dev/ttyUSB2
#echo 'ATDT*99#' > /dev/ttyUSB2
#pppd /dev/ttyUSB2 115200 mru 1280 nodetach debug dump defaultroute usepeerdns novj user IP password INTERNET novjccomp noipdefault ipcp-accept-remote connect-delay 5000

N/A

N/A

Patty 18:12, 15 September 2011 (CST)

Patty 18:12, 15 September 2011 (CST)

Test on: Ubuntu 12.04

1.Download Driver(5370)

2.Uncompress the file 3.Enable Wpa_Supplicant and Native Wpa_Supplicant for Network Manager

   #vi os/linux/config.mk
   HAS_WPA_SUPPLICANT=y
   HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
   Blacklist rt2x00usb
   #modprobe –r rt2800usb
   #reboot

4.compile driver

   #make 
   #make install
   #modprobe rt5370sta

5.add to /etc/modules

   #echo rt5370sta >> /etc/modules

Driver(5370)

N/A

Tom 2012/08/23

Tom 2011/08/23

In ubuntu and fedora
1.Watch /dev/ttyACM0 state

#cat /dev/ttyACM0 &

2.Enable GSM NETWORK

#echo -en "ATE0\r" > /dev/ttyACM0
#echo -en "AT\r" > /dev/ttyACM0
#echo -en "ATZ\r" > /dev/ttyACM0
#echo -en "AT+CGDCONT=1,"IP","INTERNET"\r" > /dev/ttyACM0
#echo -en "ATDT*99#\r" > /dev/ttyACM0

3.set new mobile broadband

1.NewWork Connection->Mobile Broadband->add
2.device:telit wireless
3.select Country or Region
4.select your provider
5.select your plan:INTERNET

4.connect

"N/A"

"N/A"

"KK 2013/09/25"

"kk 2013/9/25"

step1. open terminal
step2. #sudo dpkg -i firmware-ralink_0.36+wheezy.deb
step3. #reboot

"firmware-ralink_0.36+wheezy File"

"N/A"

"2015/07/31 KK"

"2015/07/31 KK"

1. In the Terminal, type "lsusb" to confirm if the device has been detected by the system (Qualcomm / option)
2. Enter "apt-get install wvdial" in Terminal (※ link to network)
3. Enter "wvdialconf" in the Terminal to start the device scan (it will wait a little while, if there is a scan to the device, the location of the device will appear, for example, "Find a modem on /dev/ttyUSB2", "Modem configuration written to /etc/wvdial.comf”
4. Edit this file in /etc/wvdial.conf (you can use vi, vim, gedit)
5. Enter "wvdial" in Terminal
6. Start a new Terminal execution "ifconfig" to determine if there is a new network device and IP

"wvdial.conf"

"N/a"

"N/a"

"--king kong 18:42, 17 January 2019 (CST)"