WinCheck Introduce

From LEXWiKi

(Difference between revisions)
Jump to: navigation, search
(New page: Category:AllowPages == WinCheck Instruction == Test all function on MainBoard (ex: Lan, COM, Audio...) Image:WinCheck.jpg == Function Instruction == === Setting === Records the ...)
Line 83: Line 83:
Check Report dialog, green light means successed. red light means failed.
Check Report dialog, green light means successed. red light means failed.
[[Image:report.jpg]]
[[Image:report.jpg]]
 +
 +
== FAQ ==
 +
=== It is show "Fail to retreve time from NTP server" or Sync time error when runing wincheck ===
 +
{|
 +
!bgcolor = #ccccff width="50" align="center"|Ans:
 +
!bgcolor = #F3F3F3 width="100%" align="left"|
 +
1.Ethernet connect was break off<br />
 +
2.If you can't find "Ntpd.exe" in "Task Manager" , Please follow Pach file to reinstall NTP server<br />
 +
|-
 +
!bgcolor = #ccccff |Patch File:
 +
!bgcolor = #F3F3F3 align="left"|
 +
[ftp://ftp.lex.com.tw/Engineer/SoftSupport/Q%26A/NTP_Servr/illustration.doc illustration.doc]
 +
[ftp://ftp.lex.com.tw/Engineer/SoftSupport/Q%26A/NTP_Servr/ntp-4.2.0a@1.1354-o-win32-setup.exe NTP Server]
 +
|-
 +
!bgcolor = #ccccff |Defect:
 +
!bgcolor = #F3F3F3 align="left"|
 +
"N/A"
 +
|-
 +
!bgcolor = #ccccff |Asker:
 +
!bgColor = #F3F3F3 align="left"|
 +
"Steve 2010/05/03"
 +
|-
 +
!bgcolor = #ccccff |Provider:
 +
!bgColor = #F3F3F3 align="left"|
 +
"Steve 2010/05/03"
 +
|-
 +
|}

Revision as of 15:27, 3 May 2010

Contents

WinCheck Instruction

Test all function on MainBoard (ex: Lan, COM, Audio...)

Image:WinCheck.jpg

Function Instruction

Setting

Records the user information and establishes Server IP (FTP Server, HTTP Server, NTP Server)

Hardware Monitor

Display hardware information After start of the test if this option was been checked.

Image:Monitor.jpg

Write CMOS

Write CMOS Setting

System Information 

 Display system information as below :
 1. BIOS
 2. CPU
 3. RAM
 4. HDD

NetWork Function Test 

 1. Verify MAC Address 
 2. Test 10/100 Mode TCP/UDP transmission 
 3. Test 1000 Mode TCP/UDP transmission 
 4. when WinCheck executed, adjust local time with NTP server by custmoize IP      
    ( If failured, show "Failed to retreive time from NTP server" dialog )

Image:lan.jpg

Connector Function Test

1. COM Port ( Rx/Tx Only, all ) 

  Pin Status Test
  Pin Control Test
  Transmitting Loop Test
  Baud Rate Test

Image:COM.jpg

2. LPT Port 

  Transmitting Loop Test

Image:LPT.jpg

Audio Function Test 

  Line-In Test ( Left )
  Line-In Test ( Right )
  Mic-In Test

  FI853A SPDIF Test

Image:Audio.jpg

DIO/WDT Function Test

Press WDT button will show another dialog. Select mainboard to test DIO function on this dialog.

Image:DIOWDT.jpg

Tarnasmitting Loop Test with DI/DO

Image:DO.jpg

Watch Dog Test 

 Show report dialog after all function tested. there's a "reboot" button below this dialog
 pressed this button, System will be reboot at 5 seconds later.

Image:WDT.jpg

WinCheck Report 

 Notice with buzzer after all function was finished test
 Successed : buzzer beeps 3 shorts after one long beep
 Failed    : one long beep
 Check Report dialog, green light means successed. red light means failed.

Image:report.jpg

FAQ

It is show "Fail to retreve time from NTP server" or Sync time error when runing wincheck

Ans:

1.Ethernet connect was break off
2.If you can't find "Ntpd.exe" in "Task Manager" , Please follow Pach file to reinstall NTP server

Patch File:

illustration.doc NTP Server

Defect:

"N/A"

Asker:

"Steve 2010/05/03"

Provider:

"Steve 2010/05/03"

Retrieved from "http://tprd.info/lexwiki/index.php/WinCheck_Introduce"
Personal tools